gras 46bd-s1 1/4 ccp pressure standard microphone set with smb connector
technology
introduction
through a close cooperation with our customers, we know that data-safety is highly important because the costs related to unsuited and unreliable sensors may determine whether your project turns into a success or not.
for our users, data safety translates directly into requests for easier microphone selection, simple system configuration and reduction of measurement errors.
to meet these requirements, we invented the microphone set concept. it is simple, reliable and robust and consists of a microphone cartridge and preamplifier combination, which is calibrated as one unit. this eliminates errors because there is only one sensitivity value to account for and the risk of contaminating the interface is eliminated. combine this with our unique and proven design and you have the most reliable measurement microphone sets available in the industry today.
typical applications and use
the 46bd-s1 is ideal for sound pressure measurements, as well as high frequency and high level pressure measurements. it is suitable for general purpose acoustic measurements in couplers and at boundaries.
regarding temperature range, see the specifications. should higher temperature limits be required, we recommend considering the gras probe microphones where the microphone and preamplifier can be isolated from the hot source.
design
the gras 46bd-s1 is a high-performance standard microphone set. in our clean-room environment the set is assembled and sealed with a label. however, the microphone set can be dismounted, if you wish to use the components separately.
microphone
the microphone cartridge is the high-quality iec 61094 ws3p standardized gras 40bd 1/4 prepolarized pressure microphone, designed for long-term reliability in multiple environments.
preamplifier
the preamplifier is the gras 26cc preamplifier which is inclusive teds and based on our well-known circuit board substrates. in the industry these are famous for their low self-noise, wide frequency and excellent slew rate performance.
compatibility
to perform as specified the gras 46bd-s1 microphone set requires a constant current input module that can deliver 4 ma and 24 v unloaded ccp voltage supply. if the constant current supply is lower, the capability of driving long cables is reduced and consequently the upper frequency is reduced. if the voltage supply is lower it will influence the upper dynamic range.
the microphone set is terminated with a smb connector. ready to use coax cable assemblies of various types and lengths are available in standard as well as customized lengths.
the 46bd-s1 is ieee 1451.4 teds v. 1.0 compliant. if your measurement platform supports transducer electronic data sheets you will be able to read and write data like properties and calibration data.
system verification
the functionality of teds is very useful to determine which microphone is connected to which input channel. however, it is not a check of whether the microphone is within specifications or not. for daily verification and check of your measurement setup, we therefore recommend using a sound source like the gras 42ag sound calibrator.
for proper sensitivity calibration we recommend using a reference sound source like the gras 42ap intelligent pistonphone.
gras halt
when our r&d team develops a measurement microphone, it must undergo the most demanding tests to prove that it can withstand our customers' daily test conditions. using a series of highly accelerated lifetime tests (halt) we ensure that our microphones live up to the high quality and precision that our customers have come to expect and trust. our halt tests actively accelerate the lifetime of a microphone by simulating the handling and use it is exposed to in real life situations.
service
should you by mistake damage the diaphragm on a gras microphone we will in most cases be able to exchange it at a very reasonable cost and short turn-around time. this not only protects your investment but also meets your quality assurance department since you do not have to worry about new serial numbers etc.
calibration
when leaving the factory, all gras microphones have been calibrated in a controlled laboratory environment using traceable calibration equipment. depending on the use, measurement environment and internal quality control programs we recommend that the microphone is recalibrated at least once a year.
quality and warranty
gras microphone sets are made of components from our proven standard portfolio and are all manufactured of high-quality material and branded parts that were chosen and processed to ensure life-long stability and robustness.
all parts are manufactured and assembled at the factory in denmark by skilled and dedicated operators in a verified clean-room environment. the microphone diaphragm, body and unique protection grid are made of high-grade stainless steel and make the microphone set resistant to physical damage as well as corrosion caused by aggressive air or gasses.
this, together with the enforced gold-plated microphone terminal guarantees a highly reliable connection. thanks to the high quality, our warranty against defective materials and workmanship is 5 years.